PLANET BSP-115PV-15A
Solar powered PoE+ switch with integrated MPPT controller offers 5× RJ-45 10/100/1000 Base-T with PoE+ IEEE 802.3af/at (35 W/port) , 120 W PoE budget, DIP switch and 1× SFP 100/1000 Base-X. LCD display for power information.
1× 6pin terminal block (removable), pins 1/2, 3/4 for PV (photovoltaic) panels + some types of generators (hydro or wind), pins 5/6 for battery charging/discharging . The PV input is compatible with DC input, but must not be connected at the same time as the solar input to avoid damage to the device. There is a DIP switch on the front side, which can be used to configure PoE and VLAN . The DIP switch on the back is then used to set the battery type and voltage .
ESD protection up to 4 kV (contact), up to 8 kV (air), temperature sensor (detection -20 to 100 °C), IP30 protection (metal housing), fanless, wall or table mounting, operating temperature -20 to +65 °C .
Solar PoE switch that supports simultaneous use of solar (PV) and battery power. The energy obtained from the solar panel is stored in a 12 or 24 V battery. Then, when solar power is not available, the battery is used to power the switch and connected devices.
This solution provides the ability to power connected active devices, such as IP cameras, switches, converters or Wi-Fi units, all the time and without dependence on the power grid. The application is therefore suitable for providing surveillance in the environment of parks, forests, cottages or large agricultural and industrial areas. Thanks to the uninterrupted power supply, it can also be used as a means of building telecommunication points for local Internet providers.
Battery management:
- Supports lithium (Lithium, Li-Fe) and lead-acid (Lead-acid, Pb) batteries, optional
- Input power (PV IN): min. voltage 20–27 V DC (12V battery), 32–45 V DC (24V battery), max. current 15 A, power up to 405 W (for 12V battery, 675 W for 24V battery)
- Easy diagnosis of system operating status using LED indicator
- Current battery usage status
- MPPT (Maximum Power Point Tracking) charge controller
- Reverse current protection (prevents the backflow of electrical current into the photovoltaic panel)
- Overcurrent protection and reverse polarity protection (for battery and charging electrodes)
BASIC SPECIFICATIONS
Physical properties:
Ports: 5x RJ-45 10/100/1000 Base-T with PoE+ IEEE 802.3af/at, 1x SFP Base-X
Memory: 2K MAC addresses, 2.5 Mb buffer
Throughput: 12 Gbps bus, operational 8.92 Mpps (64B)
Design: desktop, wall-mounted
Power supply (switches): via photovoltaic panels (DC 20–45 V) or from battery (DC 12/24 V), total power consumption up to 140 W (full load with PoE power supply)
Power requirements:
Solar panel: 20-27V DC (12V battery), 32-45V DC (24V battery)
Batteries: 12/24 V, lithium (Li-Fe) and lead-acid (Pb) batteries
Output power: 5× PoE+ RJ-45, 6pin terminal block (2× input for PV panel, 1× power input/output for 12/24V battery)
Protection: ESD up to 4 kV contact, 8 kV air (ethernet)
Operating temperature:-20 to +65 °C
Dimensions: 197 × 142 × 34 mm
Weight: 820g
PoE function:
Total power output: up to 120 W, 802.3af/at
Number of injectors: 5x up to 35 W
Power supply type: End-span
Advanced features:
protection (of a circuit) against interference between ports
automatic detection of powered device
detection of activity of powered devices, if there is no response, it can be restarted by disconnecting the power supply (PD alive check)
Extended mode 10 Mbps with a range of up to 250 m
The Switch has a manual mode switch:
- Alive check - monitors the status of connected devices in real time. As soon as a device stops responding, it will be put back into operation by restoring power.
- VLAN - ports are logically separated from each other, in this mode unwanted multicast and broadcast storms can be prevented.
- Extend - the switch powers devices up to 250 m with reduced throughput of 10 Mbps per port.
Other downloads
